Lighting
Martin Atomic 3000 (DMX / LED) troubleshooting
The Martin Atomic 3000 (DMX / LED) problems live-event techs bring to Ask Roadie most (also called Atomic 3000, Atomic 3000 LED, Atomic Colors, Martin strobe). Pick your symptom, or describe your own in plain words, and get the likeliest fix first, with the manual page when there is one.
Common Atomic 3000 (DMX / LED) errors & problems
What techs run into most, and what's usually behind it. The step-by-step fix for your exact unit is in Ask Roadie.
- Step-by-step fixGet the fix →
Atomic 3000 LED full specs
Likely cause: These are the manufacturer spec-sheet figures a tech needs for power, rigging weight and console patch.
- Step-by-step fixGet the fix →
Atomic Colors scroller not detected
Likely cause: The detection failure is a known v1.0.0 firmware bug plus cable/connection issues; wrong cable or old firmware are the two root causes.
- Step-by-step fixGet the fix →
Classic xenon Atomic 3000 DMX - which lamp/flashtube?
Likely cause: Using the correct lamp for the units mains voltage is essential; the tube is the part that wears out on the xenon version.
- Step-by-step fixGet the fix →
Gels melting or burning in the Atomic Colors scroller
Likely cause: Heat management depends on the fixture knowing a scroller is fitted; undetected scroller + full output is what cooks the gels.
- Step-by-step fixGet the fix →
How do I set the DMX address and navigate the menu?
Likely cause: The base channel plus channel-count determines where each fixture listens; duplicate addresses are why two units mirror each other.
- Step-by-step fixGet the fix →
How do I update firmware on the Atomic 3000 LED?
Likely cause: Companion is the current Martin tool for pushing firmware; verifying the installed version avoids re-flashing unnecessarily.
- Step-by-step fixGet the fix →
Mandatory firmware update (scroller detection bug)
Likely cause: Martin issued this as mandatory specifically to prevent gel/heat damage and instability from the v1.0.0 bug.
- Step-by-step fixGet the fix →
Power and breaker planning for Atomic 3000 LED
Likely cause: Strobes are peaky loads; planning to rated current alone under-sizes the circuit and trips breakers on heavy strobe cues.
- Step-by-step fixGet the fix →
Run strobes without a console (standalone / master-slave)
Likely cause: Master-slave lets a rig run a synced chase off one lead fixture when there is no desk.
- Step-by-step fixGet the fix →
What DMX channel modes does the Atomic 3000 LED use?
Likely cause: Mismatched mode vs console profile is the usual cause of channels doing the wrong thing; extended mode is required to reach Aura and scroller.
- Step-by-step fixGet the fix →
Xenon Atomic 3000 not flashing or very weak flash
Likely cause: Flashtubes lose output and eventually stop firing as they age; matching lamp to mains voltage prevents damage and weak output.
Not on the list? Describe it your way, or paste the error code off the display. Ask Roadie works the problem with you until it's fixed or you have a clear next move.
How Ask Roadie helps with the Atomic 3000 (DMX / LED)
- 1. Pick the Martin Atomic 3000 (DMX / LED). It's already in the list.
- 2. Describe what you're seeing. In your own words, or the error code off the screen.
- 3. Get the likeliest fix first. Steps in order, the manual page when there is one, and a note when other techs have confirmed it.
- 4. Still broken? Tap 👎 and it keeps going from where you left off.
Free trial
Get your Atomic 3000 (DMX / LED) back up before doors.
Try it free. No card required.
Start free trial →